Manufacturers / Mizuno / ST-X 230 Driver / Compatible shafts
Sleeve fitMizuno ST-X 230 Driver compatible shafts
The ST-X 230 Driver uses the Mizuno Quick Switch (230 Series) adapter (Mizuno connector system), Quick Switch (ST-X 230 / ST-Z 230 / ST-G, 2023; JPX One / JPX One Select, 2026) (0.335" tip).
Check your shaft
Type the model your shaft is currently in (or was pulled from) to see whether it fits the ST-X 230 Driver.
Drops straight in
Both use the , " tip. No reshaft, no builder. Re-check your loft position after the swap.
Fits, after an adapter swap
Not a drop-in. This shaft carries a ; the ST-X 230 Driver needs a . The shaft itself works: a club builder swaps the adapter for a small shop fee.
The shaft's " tip differs from this head's " tip, so the builder may need to re-tip it; it may not be a clean swap.
Does not fit
Fits, after an adapter install
That shaft has no adapter, it is glued into a fixed hosel. A club builder can cut it and install a adapter to make it fit this head.
Fit unknown
We have not verified that model's hosel hardware yet, so we cannot say whether its shaft carries an adapter or is glued in. Treat this combination as unknown rather than assuming a fit.
Not in our catalog
That model is not in our catalog yet. Report it so we can add it, rather than guess.
Sleeve interchange
Researched cases where a sleeve from another generation of this same brand does or does not fit this head.
| Sleeve family | Verdict | Notes | Source |
|---|---|---|---|
| Mizuno Quick Switch Fairway | Does not fit | This driver's Quick Switch DRIVER sleeve is a different part than the Quick Switch FAIRWAY sleeve. | Inferred from aftermarket sleeve part coverage, cross-checked across suppliers. |
Shafts that drop in from another head
Mizuno ships this sleeve under two labels that interchange: Mizuno Quick Switch (ST200 Series) and Mizuno Quick Switch (230 Series).
Inferred from aftermarket sleeve part coverage, cross-checked across suppliers.
A shaft pulled from any of these heads carries a sleeve the ST-X 230 Driver accepts, so it drops straight in, no reshaft.
- Mizuno GT180 DriverQuick Switch ST200 Series
- Mizuno JPX One DriverQuick Switch 230 Series
- Mizuno JPX One Select DriverQuick Switch 230 Series
- Mizuno ST-G 220 DriverQuick Switch ST200 Series
- Mizuno ST-G DriverQuick Switch 230 Series
- Mizuno ST-MAX 230 DriverQuick Switch 230 Series
- Mizuno ST-X 220 DriverQuick Switch ST200 Series
- Mizuno ST-X DriverQuick Switch ST200 Series
- Mizuno ST-Z 220 DriverQuick Switch ST200 Series
- Mizuno ST-Z 230 DriverQuick Switch 230 Series
- Mizuno ST-Z DriverQuick Switch ST200 Series
- Mizuno ST180 DriverQuick Switch ST200 Series
- Mizuno ST190 DriverQuick Switch ST200 Series
- Mizuno ST190G DriverQuick Switch ST200 Series
- Mizuno ST200 DriverQuick Switch ST200 Series
- Mizuno ST200G DriverQuick Switch ST200 Series
- Mizuno ST200X DriverQuick Switch ST200 Series
Stock shaft
Any 0.335 inch tip shaft can be built for this hosel by a club builder; the sleeve, not the shaft model, is what decides whether a used pull drops in.
Shafts from other brands
Sleeve adapters are brand specific. A shaft pulled from a different brand's head carries that brand's sleeve, not this one, so it needs the sleeve swapped by a club builder before it fits this head.
Fit from Mizuno ST-Z 230 / ST-X 230 Adaptability Chart.
Adapter settings chart: what every position does
Thanks. We verify every report against a source before updating the data.
Something went wrong with that report. Please try again.