Manufacturers / Honma / TW777 360 Ti Driver / Compatible shafts
Sleeve fitHonma TW777 360 Ti Driver compatible shafts
The TW777 360 Ti Driver uses the Honma TR20 460 Non-Rotating Adjustable Hosel adapter (Honma connector system), Honma Non-Rotating Adjustable Hosel (TW747-era through current Tour World / select BERES generations) (0.339" tip).
Check your shaft
Type the model your shaft is currently in (or was pulled from) to see whether it fits the TW777 360 Ti Driver.
Drops straight in
Both use the , " tip. No reshaft, no builder. Re-check your loft position after the swap.
Fits, after an adapter swap
Not a drop-in. This shaft carries a ; the TW777 360 Ti Driver needs a . The shaft itself works: a club builder swaps the adapter for a small shop fee.
The shaft's " tip differs from this head's " tip, so the builder may need to re-tip it; it may not be a clean swap.
Does not fit
Fits, after an adapter install
That shaft has no adapter, it is glued into a fixed hosel. A club builder can cut it and install a adapter to make it fit this head.
Fit unknown
We have not verified that model's hosel hardware yet, so we cannot say whether its shaft carries an adapter or is glued in. Treat this combination as unknown rather than assuming a fit.
Not in our catalog
That model is not in our catalog yet. Report it so we can add it, rather than guess.
Sleeve interchange
Researched cases where a sleeve from another generation of this same brand does or does not fit this head.
| Sleeve family | Verdict | Notes | Source |
|---|---|---|---|
| Honma Fairway Adapter (TW777/TR21 generation) | Does not fit | Driver-generation Honma adapter (honma-tr20-hosel) is not interchangeable with the fairway-generation adapter (honma-fairway-hosel): The Golf Club Trader sells these as separate, distinctly-titled SKUs ('Honma Driver Adapter Sleeve for TW767 TW757 TR20 Tour World XP-1 TW747' for drivers, scoped verbatim to 'Drivers' in its own listing, versus 'Honma Fairway Adapter Sleeve for TW777, TR21 Fairway Wood' for fairways), confirming a physically distinct part despite the shared Non-Rotating System mechanism family and matching .335 tip diameter. | Inferred from aftermarket sleeve part coverage, cross-checked across suppliers. |
Shafts that drop in from another head
A shaft pulled from any of these heads carries a sleeve the TW777 360 Ti Driver accepts, so it drops straight in, no reshaft.
- Honma Beres Nx Driver
- Honma Malbon x Honma Premium Driver
- Honma T//World GS Driver
- Honma TR20 440 Driver
- Honma TR20 460 Driver
- Honma TW747 455 Driver
- Honma TW747 460 Driver
- Honma TW757 D-Plus 2 Driver
- Honma TW757 D-Plus Driver
- Honma TW757 Type-D Driver
- Honma TW757 Type-S Driver
- Honma TW767 Driver
- Honma TW767 LS Driver
- Honma TW767 Max Driver
- Honma TW777 Driver
- Honma TW777 Max Driver
- Honma XP-1 Driver
Any 0.339 inch tip shaft can be built for this hosel by a club builder; the sleeve, not the shaft model, is what decides whether a used pull drops in.
Shafts from other brands
Sleeve adapters are brand specific. A shaft pulled from a different brand's head carries that brand's sleeve, not this one, so it needs the sleeve swapped by a club builder before it fits this head.
Fit from Honma TR20 460 Driver Product Page (HK).
Thanks. We verify every report against a source before updating the data.
Something went wrong with that report. Please try again.